| After-sales Service: | Lifelong |
|---|---|
| Function: | Measurement of Lcr |
| Display: | 7-Inch (Diagonal)TFT LCD Display |
| Usage: | Electric Component Tester, Gas Sensor Tester, Catalytic Element Tester, Lightning Protection Device Tester, Lcr Meter |
| Type: | Lcr Meter |
| Environment: | Room Temperature |
| Customization: |
|---|
Suppliers with verified business licenses
Audited Supplier Brief Introduction
TH2838H is a new generation impedance tester adopting the most advanced auto balance bridge theory in the world at present. With its 0.05% basic accuracy, speed up to 5.6ms, 20Hz-2MHz frequency range and impedance test range up to 1GΩ, this new impedance tester can meet all test demands of components and materials, especially for testing capacitor with low D and inductor with high Q. Four-terminal pair configuration can eliminate the effect of electromagnetic coupling in test cable, to extend the low limit of low impedance test 10 times than those testers with Five-pair configuration.
TH2838H supports 20V AC test signal and 40V DC Bias, new-added improved multi parameter list sweep/graphic analyze will help customers to extend the comprehensive evaluation ability on components.
TH2838H is a strong tool for the design, examination, quality control and production test of electronic components. Its excellent performances and functions provide a powerful tool for circuit design and development, as well as material (electronic material and non-electronic material) research and development.
TH2838H can realize various tests of commercial standards and military standards, such as IEC and MIL.
Technical Parameter
| Model | TH2838H | |||||||||
| Test Signal Source | ||||||||||
| Output impedance | 100Ω, ±1% @1kHz | |||||||||
| Frequency | Range | 20Hz-2MHz | ||||||||
| Resolution | 20.0000Hz - 99.9999Hz 0.1mHz | |||||||||
| 100.000Hz - 999.999Hz 1mHz | ||||||||||
| 1.00000kHz - 9.99999kHz 10mHz | ||||||||||
| 10.0000kHz - 99.9999kHz 0.1Hz | ||||||||||
| 100.000kHz - 999.999kHz 1Hz | ||||||||||
| 1.00000MHz - 2.00000MHz 10Hz | ||||||||||
| AC test signal | Rated value(ALC OFF):Set the voltage as the Hcur voltage when the test terminal is open Set the current as the Hcur current when the test terminal is short Constant value(ALC ON):Keep the voltage in DUT is the same as the set valueKeep the current in DUT is the same as the set value | |||||||||
| AC signal | Voltage range | F≤1MHz 5mVrms--20Vrms F>1MHz 5mVrms--15Vrms | ||||||||
| Resolution | 5mVrms -- 0.2Vrms 100μVrms | |||||||||
| 0.2Vrms -- 0.5Vrms 200μVrms | ||||||||||
| 0.5Vrms -- 1Vrms 500μVrms | ||||||||||
| 1Vrms -- 2Vrms 1mVrms | ||||||||||
| 2Vrms -- 5Vrms 2mVrms | ||||||||||
| 5Vrms -- 10Vrms 5mVrms | ||||||||||
| 10Vrms -- 20Vrms 10mVrms | ||||||||||
| Current range | 50μArms --100mArms | |||||||||
| Resolution | 50μArms -- 2mArms 1 μArms | |||||||||
| 2mArms -- 5mArms 2 μArms | ||||||||||
| 5mArms -- 10mArms 5 μArms | ||||||||||
| 10mArms -- 20mArms 10μArms | ||||||||||
| 20mArms -- 50mArms 20μArms | ||||||||||
| 50mArms--100mArms 50μArms | ||||||||||
| Rdc test | Voltage range | 100mV - 2V | ||||||||
| Resolution | 100μV | |||||||||
| Current range | 0mA- 20mA | |||||||||
| Resolution | 1μA | |||||||||
| DC Bias | Voltage range | 0V - ± 40V | ||||||||
| Resolution | 0V -- 5V 100μV | |||||||||
| 5V -- 10V 1mV | ||||||||||
| 10V -- 20V 2mV | ||||||||||
| 20V -- 40V 5mV | ||||||||||
| Current range | 0mA- ± 100mA | |||||||||
| Resolution | 0 A -- 50mA 1μA | |||||||||
| 50mA -- 100mA 10μA | ||||||||||
| Voltage source | Voltage range | -10V -- 10V | ||||||||
| Resolution | 1mV | |||||||||
| Current range | -45mA -- +45mA | |||||||||
| Output impedance | 100Ω | |||||||||
| Display | ||||||||||
| Dimensions /typ | 7-inch (diagonal)TFT LCD display | |||||||||
| Proportion | 16:9 | |||||||||
| Resolution | 800×RGB×480 | |||||||||
| Test function | ||||||||||
| Test parameter | Cp-D,Cp-Q,Cp-G,Cp-RpCs-D,Cs-Q,Cs-RsLp-D, Lp-Q, Lp-G, Lp-Rp, Lp-RdcLs-D, Ls-Q, Ls-Rs, Ls-Rdc, RdcR-X, Z-θd, Z-θrG-B, Y-θd, Y-θrVdc-Idc | |||||||||
| Mathematics function | A(X+B)+C, X is test parameter, A, B,C is input parameter | |||||||||
| Equivalent circuit | Series, parallel | |||||||||
| Deviation measurement | Absolute deviation Δ compared with the nominal valuePercentage deviation Δ% compared with the nominal value | |||||||||
| Calibration function | OPEN, SHORT, LOAD | |||||||||
| Range selection | AUTO, HOLD | |||||||||
| Range | LCR | 100mΩ, 1Ω, 10Ω, 20Ω, 50Ω, 100Ω, 200Ω, 500Ω, 1kΩ, 2kΩ, 5kΩ, 10kΩ, 20kΩ, 50kΩ, 100kΩ, total 15 ranges | ||||||||
| Rdc | 1Ω, 10Ω, 20Ω, 50Ω, 100Ω, 200Ω, 500Ω, 1kΩ, 2kΩ, 5kΩ, 10kΩ, 20kΩ, 50kΩ, 100kΩ, total 15 ranges | |||||||||
| Trigger mode | INT, MAN, EXT, BUS | |||||||||
| Trigger delay | 0 s -- 999 s, resolution 100us | |||||||||
| Test terminal configuration | Four-pair | |||||||||
| Test cable length | 0m, 1m | |||||||||
| Test average | 1-255 times | |||||||||
| Test time(ms) | Speed mode | 20Hz | 100Hz | 1kHz | 10kHz | 100kHz | 1MHz | 2MHz | ||
| FAST | 330 | 100 | 20 | 7.7 | 5.7 | 5.6 | 5.6 | |||
| MED | 380 | 180 | 110 | 92 | 89 | 88 | 88 | |||
| LONG | 480 | 300 | 240 | 230 | 220 | 220 | 220 | |||
| Test display range a 1×10-18 ; E 1×1018 | ||||||||||
| Cs, Cp | ±1.000000 aF -- 999.9999 EF | |||||||||
| Ls,Lp | ±1.000000 aH -- 999.9999 EH | |||||||||
| D | ±0.000001 -- 9.999999 | |||||||||
| Q | ±0.01 -- 99999.99 | |||||||||
| R, Rs, Rp, X, Z, Rdc | ±1.000000 aΩ -- 999.9999 EΩ | |||||||||
| G,B,Y | ±1. 000000 aS -- 999.9999 ES | |||||||||
| Vdc | ±1.000000 aV -- 999.9999 EV | |||||||||
| Idc | ±1.000000 aA -- 999.9999 EA | |||||||||
| θ r | ±1.000000 a rad -- 3.141593 rad | |||||||||
| θ d | ±0.0001 deg -- 180.0000 deg | |||||||||
| Δ% | ±0.0001% -- 999.9999% | |||||||||
| t | -99.99°C -- 1000.00°C | |||||||||
| Turn Ratio (extension pending) | ±0.000000 -- 1000.000 | |||||||||
| Basic test accuracy | 0.05% (the details refer to the instruction) | |||||||||
| List sweep | ||||||||||
| Sweep points | Up to 201 points | |||||||||
| Sweep Parameters | Test frequency, AC voltage, AC current, DC BIAS voltage, DC BIAS current | |||||||||
| Trigger mode | SEQ | Once triggered, test at the sweep points. /EOM/INDEX will be output one time. | ||||||||
| STEP | Once triggered, test at one sweep point. /EOM/INDEX will be output at each point, but the list sweep comparator results only be output at the last /EOM. | |||||||||
Chuangkai Electronic Co., Ltd is leading company specialized in producing, developing & selling various types of measuring instruments and testing equipment, such as temperature data logger, LCR meter, DC resistance tester (micro ohm meter), digital power meter, power supply, transformer tester, battery tester, programmable DC electronic load, charger, temperature controller, tachometer, high voltage signal-amplifier, power amplifier, etc.
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}